Everything below concerns Quality control. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2026-06-15. Where a claim depends on a specific study, the study is described rather than over-claimed.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
Atoltivimab/maftivimab/odesivimab, sold under the brand name INMAZEB, is a fixed-dose combination of three monoclonal antibodies for the treatment of ebola caused by Zaire ebolavirus. It was developed by Regeneron Pharmaceuticals and contains three human monoclonal antibodies, atoltivimab, maftivimab, and odesivimab-ebgn. The most common side effects include fever, chills, tachycardia (fast heart rate), tachypnea (fast breathing), and vomiting; however, these are also common symptoms of Ebola virus infection. Atoltivimab/maftivimab/odesivimab is the first FDA-approved treatment for Zaire ebolavirus. Atoltivimab/maftivimab/odesivimab was approved for medical use in the United States in October 2020. The U.S. Food and Drug Administration (FDA) considers it to be a first-in-class medication. It is on the World Health Organization's List of Essential Medicines. Atoltivimab/maftivimab/odesivimab is indicated for the treatment of infection caused by Zaire ebolavirus.
“Chemoinformatics and Molecular Simulation”; “Chemistry of Supramolecular Nano- and Biosystems”; “Methods of Analytical Chemistry”; “Physical-Chemical Methods in Chemistry”; “Petrochemistry and Catalysis”. Total number of students taking Bachelor, Specialist and master's degree programs is 472 (as of January, 2016).Departments of the Institute of Chemistry educate postgraduates in the following majors: 02.00.01 – Inorganic Chemistry; 02.00.02 – Analytical Chemistry; 02.00.03 – Organic Chemistry; 02.00.04 – Physical Chemistry; 02.00.08 – Chemistry of Organoelement Compounds. There are two dissertation councils functioning in the Institute of Chemistry for thesis defence in chemical sciences: Д 212.081.03 under the Federal State Autonomous Institution of Higher Education “Kazan (Volga Region) Federal University”; majors allowed for defence: 02.00.01 – Inorganic Chemistry; 02.00.08 – Chemistry of Organoelement Compounds; Chairman of the Council is Professor Vladimir I. Galkin, Doctor of Chemistry;
H3A (aq) + H2O (l) ⇌ H3O+ (aq) + H2A− (aq) Ka1 H2A− (aq) + H2O (l) ⇌ H3O+ (aq) + HA2− (aq) Ka2 HA2− (aq) + H2O (l) ⇌ H3O+ (aq) + A3− (aq) Ka3 An inorganic example of a triprotic acid is orthophosphoric acid (H3PO4), usually just called phosphoric acid. All three protons can be successively lost to yield H2PO−4, then HPO2−4, and finally PO3−4, the orthophosphate ion, usually just called phosphate. Even though the positions of the three protons on the original phosphoric acid molecule are equivalent, the successive Ka values differ since it is energetically less favorable to lose a proton if the conjugate base is more negatively charged. An organic example of a triprotic acid is citric acid, which can successively lose three protons to finally form the citrate ion. Although the subsequent loss of each hydrogen ion is less favorable, all of the conjugate bases are present in solution. The fractional concentration, α (alpha), for each species can be calculated. For example, a generic diprotic acid will generate 3 species in solution: H2A, HA−, and A2−. The fractional concentrations can be calculated as below when given either the pH (which can be converted to the [H+]) or the concentrations of the acid with all its conjugate bases:
The human form of IAPP has the amino acid sequence KCNTATCATQRLANFLVHSSNNFGAILSSTNVGSNTY, with a disulfide bridge between cysteine residues 2 and 7. Both the amidated C-terminus and the disulfide bridge are necessary for the full biological activity of amylin. IAPP is capable of forming amyloid fibrils in vitro. Within the fibrillization reaction, the early prefibrillar structures are extremely toxic to beta-cell and insuloma cell cultures. Later amyloid fiber structures also seem to have some cytotoxic effect on cell cultures. Studies have shown that fibrils are the end product and not necessarily the most toxic form of amyloid proteins/peptides in general. A non-fibril forming peptide (1–19 residues of human amylin) is toxic like the full-length peptide but the respective segment of rat amylin is not. It was also demonstrated by solid-state NMR spectroscopy that the fragment 20-29 of the human-amylin fragments membranes. Rats and mice have six substitutions (three of which are proline substitutions at positions 25, 28 and 29) that are believed to prevent the formation of amyloid fibrils, although not completely as seen by its propensity to form amyloid fibrils in vitro. Rat IAPP is nontoxic to beta-cells when overexpressed in transgenic rodents.
Sources: en.wikipedia.org
RCO2H + R'2NH → RCO−2 + R'2NH+2 RCO−2 + R'2NH+2 → RC(O)NR'2 + H2O Esters are far superior substrates relative to carboxylic acids. Further "activating" both acid chlorides (Schotten-Baumann reaction) and anhydrides (Lumière–Barbier method) react with amines to give amides: RCO2R" + R'2NH → RC(O)NR'2 + R"OH RCOCl + 2R'2NH → RC(O)NR'2 + R'2NH+2Cl− (RCO)2O + R'2NH → RC(O)NR'2 + RCO2H Peptide synthesis use coupling agents such as HATU, HOBt, or PyBOP. The hydrolysis of nitriles is conducted on an industrial scale to produce fatty amides. Laboratory procedures are also available. Many specialized methods also yield amides. A variety of reagents, e.g. tris(2,2,2-trifluoroethyl) borate have been developed for specialized applications. Amidogen Amino radical Imidic acid Metal amides IUPAC Compendium of Chemical Terminology
Alcohol dehydrogenase class-3 is an enzyme that in humans is encoded by the ADH5 gene. This gene encodes glutathione-dependent formaldehyde dehydrogenase or the class III alcohol dehydrogenase chi subunit, which is a member of the alcohol dehydrogenase family. Members of this family metabolize a wide variety of substrates, including ethanol, retinol, other aliphatic alcohols, hydroxysteroids, and lipid peroxidation products. Class III alcohol dehydrogenase is a homodimer composed of 2 chi subunits. It has virtually no activity for ethanol oxidation, but exhibits high activity for oxidation of long-chain primary alcohols and for oxidation of S-hydroxymethyl-glutathione, a spontaneous adduct between formaldehyde and glutathione. This enzyme is an important component of cellular metabolism for the elimination of formaldehyde, a potent irritant and sensitizing agent that causes lacrymation, rhinitis, pharyngitis, and contact dermatitis.
Albert Lester Lehninger (February 17, 1917 – March 4, 1986) was an American chemist in the field of bioenergetics. He made fundamental contributions to the current understanding of metabolism at a molecular level. In 1948, he discovered, with Eugene P. Kennedy, that mitochondria are the site of oxidative phosphorylation in eukaryotes, which ushered in the modern study of energy transduction. He is the author of a number of classic texts, including Biochemistry, The Mitochondrion, Bioenergetics and, most notably, his series Principles of Biochemistry. This last is a widely used text for introductory biochemistry courses at the college and university levels. Lehninger was born in Bridgeport, Connecticut, US. He earned his BA in English from Wesleyan University (1939) and went on to earn both his MA (1940) and PhD (1942) at the University of Wisconsin–Madison. His doctoral research involved the metabolism of acetoacetate and fatty acid oxidation by liver cells.
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
It measures the presence and amount of one or more compounds in a liquid sample. Separation occurs in a column, and detection produces a signal proportional to concentration. Identification usually requires comparison with a known reference standard under the same conditions.