This is a working overview of Mobile phase, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2026-02-02 and is reviewed periodically as new material appears.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Actovegin is a highly filtered extract obtained from calf blood which enhances aerobic oxidation in mammals. This improves absorption of glucose and oxygen uptake in tissue, which may enhance physical performance and stamina. Local utilisation is allowed in countries like Canada and Sweden. Doctors like Hans-Wilhelm Müller-Wohlfahrt and Richard Steadman think Actovegin should be allowed in general. Others think there is not enough research, and persons from the World Anti-Doping Agency like Olivier Rabin is sceptical that it is having more than a placebo effect. Actovegin made headlines from 2009 to 2011 when Canadian sports doctor Anthony Galea was charged with drug smuggling, conspiring to lie to federal agents, unlawful possession with intent to distribute and practising medicine without a licence in the United States. Galea pleaded guilty of bringing misbranded and unapproved drugs, including Nutropin, a human growth hormone, and Actovegin, into the United States. The discipline committee for the College of Physicians and Surgeons of Ontario (CPSO) suspended Galeas license for 9 months for professional misconduct.
The increasing amount of genomic and molecular information is the basis for understanding higher-order biological systems, such as the cell and the organism, and their interactions with the environment, as well as for medical, industrial and other practical applications. The KEGG resource provides a reference knowledge base for linking genomes to biological systems, categorized as building blocks in the genomic space (KEGG GENES), the chemical space (KEGG LIGAND), wiring diagrams of interaction networks and reaction networks (KEGG PATHWAY), and ontologies for pathway reconstruction (BRITE database). The KEGG PATHWAY database is a collection of manually drawn pathway maps for metabolism, genetic information processing, environmental information processing such as signal transduction, ligand–receptor interaction and cell communication, various other cellular processes and human diseases, all based on extensive survey of published literature.
The ABC domain consists of two domains, the catalytic core domain similar to RecA-like motor ATPases and a smaller, structurally diverse α-helical subdomain that is unique to ABC transporters. The larger domain typically consists of two β-sheets and six α helices, where the catalytic Walker A motif (GXXGXGKS/T where X is any amino acid) or P-loop and Walker B motif (ΦΦΦΦD, of which Φ is a hydrophobic residue) is situated. The helical domain consists of three or four helices and the ABC signature motif, also known as LSGGQ motif, linker peptide or C motif. The ABC domain also has a glutamine residue residing in a flexible loop called Q loop, lid or γ-phosphate switch, that connects the TMD and ABC. The Q loop is presumed to be involved in the interaction of the NBD and TMD, particularly in the coupling of nucleotide hydrolysis to the conformational changes of the TMD during substrate translocation. The H motif or switch region contains a highly conserved histidine residue that is also important in the interaction of the ABC domain with ATP. The name ATP-binding cassette is derived from the diagnostic arrangement of the folds or motifs of this class of proteins upon formation of the ATP sandwich and ATP hydrolysis.
Enzymes incur catalysis by binding more strongly to transition states than substrates and products. At the catalytic binding site, several different interactions may act upon the substrate. These range from electric catalysis, acid and base catalysis, covalent catalysis, and metal ion catalysis. These interactions decrease the activation energy of a chemical reaction by providing favorable interactions to stabilize the high energy molecule. Enzyme binding allows for closer proximity and exclusion of substances irrelevant to the reaction. Side reactions are also discouraged by this specific binding. Types of enzymes that can perform these actions include oxidoreductases, transferases, hydrolases, lyases, isomerases, and ligases. For instance, the transferase hexokinase catalyzes the phosphorylation of glucose to make glucose-6-phosphate. Active site residues of hexokinase allow for stabilization of the glucose molecule in the active site and spur the onset of an alternative pathway of favorable interactions, decreasing the activation energy.
3-phosphoglycerate can be separated and measured using paper chromatography as well as with column chromatography and other chromatographic separation methods. It can be identified using both gas-chromatography and liquid-chromatography mass spectrometry and has been optimized for evaluation using tandem MS techniques. 2-Phosphoglyceric acid Calvin-Benson cycle Photosynthesis Ribulose 1,5-bisphosphate
Sources: en.wikipedia.org
A carboxylic acid has the general formula R-C(O)OH, where R is an organic radical. The carboxyl group -C(O)OH contains a carbonyl group, C=O, and a hydroxyl group, O-H. Acetic acid (CH3COOH) Citric acid (C6H8O7) Formic acid (HCOOH) Gluconic acid HOCH2-(CHOH)4-COOH Lactic acid (CH3-CHOH-COOH) Oxalic acid (HOOC-COOH) Tartaric acid (HOOC-CHOH-CHOH-COOH) Halogenation at alpha position increases acid strength, so that the following acids are all stronger than acetic acid. Fluoroacetic acid Trifluoroacetic acid Chloroacetic acid Dichloroacetic acid Trichloroacetic acid Normal carboxylic acids are the direct union of a carbonyl group and a hydroxyl group. In vinylogous carboxylic acids, a carbon-carbon double bond separates the carbonyl and hydroxyl groups. Ascorbic acid Deoxyribonucleic acid (DNA) Ribonucleic acid (RNA) Listing of strengths of common acids and bases Zumdahl, Steven S. (1997). Chemistry (4th ed.). Boston: Houghton Mifflin. ISBN 9780669417944. Pavia, D. L.; Lampman, G. M.; Kriz, G. S. (2004). Organic Chemistry Volume I. Mason, OH: Cengage Learning. ISBN 0759347271.
Normally pathogenic bacteria are weakened so they are no longer pathogenic. Commensal or food-grade bacteria which are not pathogenic. Using bacterial surface display of antigens is a valuable alternative to conventional vaccine design for various reasons, one of them being that the proteins expressed on the bacterial cell surface can act favourably as an adjuvant. Conventional vaccines require the addition of adjuvants. Another advantage of generating vaccines using bacterial display systems is that the whole bacterial cell can be incorporated in the live vaccine Unlike bacteriophage display systems which are generally used in vaccine development to find unknown epitopes, bacterial display systems are used to express known epitopes and the cells act as a vaccine delivery system. Under similar conditions, selection of bacterial-displayed peptides to model protein streptavidin proved worse.
In addition to regulating the experiments that were conducted, the guidelines also forbade the performance of other experiments. One such experiment was the cloning of recombinant DNAs derived from highly pathogenic organisms. In addition, neither the cloning of DNA containing toxin genes nor large-scale experiments using recombinant DNAs that were able to make products that were potentially harmful to humans, animals, or plants were allowed under the guidelines. These experiments were banned because the potential biohazards could not be contained by the then-current safety precautions.
The first studies measuring drugs in biological fluids were carried out to determine possible overdosing as part of the new science of forensic medicine/toxicology. Initially, nonspecific assays were applied to measuring drugs in biological fluids. These were unable to discriminate between the drug and its metabolites; for example, aspirin (c. 1900) and sulfonamides (developed in the 1930s) were quantified by the use of colorimetric assays. Antibiotics were quantified by their ability to inhibit bacterial growth. The 1930s also saw the rise of pharmacokinetics, and as such the desire for more specific assays. Modern drugs are more potent, which has required more sensitive bioanalytical assays to accurately and reliably determine these drugs at lower concentrations. This has driven improvements in technology and analytical methods. Some techniques commonly used in bioanalytical studies include:
Sources: en.wikipedia.org
The mechanism of action of biguanides is not fully understood, and many mechanisms have been proposed for metformin. Biguanides do not affect the output of insulin, unlike other hypoglycemic agents such as sulfonylureas and meglitinides. Therefore, they are effective in Type 2 diabetics; and in Type 1 diabetes when used in conjunction with insulin therapy. Mainly used in Type II diabetes, metformin is considered to increase insulin sensitivity in vivo, resulting in reduced plasma glucose concentrations, increased glucose uptake, and decreased gluconeogenesis. However, in hyperinsulinemia, biguanides can lower fasting levels of insulin in plasma. Their therapeutic uses derive from their tendency to reduce gluconeogenesis in the liver, and, as a result, reduce the level of glucose in the blood. Biguanides also tend to make the cells of the body more willing to absorb glucose already present in the bloodstream, and there again reducing the level of glucose in the plasma. Biguanides have been shown to interact with copper, specifically in mitochondria, where they interfere with cell metabolism by chelating Copper in its 2+ oxidation state (Cu(II)).
The G protein-coupled receptor kinases (GRKs) are protein kinases that phosphorylate only active GPCRs. G-protein-coupled receptor kinases (GRKs) are key modulators of G-protein-coupled receptor (GPCR) signaling. They constitute a family of seven mammalian serine-threonine protein kinases that phosphorylate agonist-bound receptor. GRKs-mediated receptor phosphorylation rapidly initiates profound impairment of receptor signaling and desensitization. Activity of GRKs and subcellular targeting is tightly regulated by interaction with receptor domains, G protein subunits, lipids, anchoring proteins and calcium-sensitive proteins. Phosphorylation of the receptor can have two consequences:
VIP is highly localised in lungs (70%) and binds with alveolar type II (AT II) cells via VPAC1. The biological (vasodilator) activity of vasoactive intestinal peptide (VIP) was discovered in the lungs before the peptide was isolated and chemical identity characterized from intestine. VIP levels are also considerably high in the brain and the gut. It is localized in key sites in the lung, has potent activities on its major functions, and appears to play an important role in pulmonary physiology and disease. The principal localization of VIP-containing neurons in the tracheobronchial tree is in the smooth muscle layer, around submucosal mucous glands and in the walls of pulmonary and bronchial arteries. Immunoreactive VIP is also present in neuronal cell bodies forming microglia that provide a source of intrinsic innervation of pulmonary structures.
Antibody diversification typically occurs through somatic hypermutation, class switching, and affinity maturation targeting the BCR gene loci, but on occasion more unconventional forms of diversification have been documented. For example, in the case of malaria caused by Plasmodium falciparum, some antibodies from those who had been infected demonstrated an insertion from chromosome 19 containing a 98-amino acid stretch from leukocyte-associated immunoglobulin-like receptor 1, LAIR1, in the elbow joint. This represents a form of interchromosomal transposition. LAIR1 normally binds collagen, but can recognize repetitive interspersed families of polypeptides (RIFIN) family members that are highly expressed on the surface of P. falciparum-infected red blood cells. In fact, these antibodies underwent affinity maturation that enhanced affinity for RIFIN but abolished affinity for collagen. These "LAIR1-containing" antibodies have been found in 5–10% of donors from Tanzania and Mali, though not in European donors. European donors did show 100–1000 nucleotide stretches inside the elbow joints as well, however. This particular phenomenon may be specific to malaria, as infection is known to induce genomic instability.
ADAM (A Database of Anti-Microbial peptides) Archived 2015-06-17 at the Wayback Machine at ntou.edu.tw AntiFP Prediction of antifungal peptides AntiMPmod Prediction of antimicrobial potential of modified peptides Antimicrobial+Cationic+Peptides at the U.S. National Library of Medicine Medical Subject Headings (MeSH) AntiTbPred Prediction of anti-tuberculosis peptides Antimicrobial Peptide Database Archived 2011-07-20 at the Wayback Machine at University of Nebraska Medical Center Antimicrobial Peptide Scanner Deep Learning based AMP prediction server AntiTbPdb Anti Tubercular Peptide Database BioPD[link removed] at Peking University Health Science Center CAMP:Collection of Anti-Microbial Peptides at National Institute for Research in Reproductive Health (NIRRH) DBAASP - Database of Antimicrobial Activity and Structure of Peptides] LAMP at Fudan University PeptideLocator Prediction of functional peptides, including antimicrobial peptides, in a protein sequence PeptideRanker Bioactive peptide, including antimicrobial peptide, prediction modlAMP Python package for computational work with antimicrobial peptides, including sequence handling, -design, -prediction, descriptor calculation and plotting
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.