accuracy is one of those subjects where the details matter more than the headlines. This page pulls together the background, the mechanisms, and the practical points readers ask about most.
Updated 2025-08-14. Numbers and descriptions here follow the published literature rather than marketing material.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
An aldehyde tag is a short peptide tag that can be further modified to add fluorophores, glycans, PEG (polyethylene glycol) chains, or reactive groups for further synthesis. A short, genetically-encoded peptide with a consensus sequence LCxPxR is introduced into fusion proteins, and by subsequent treatment with the formylglycine-generating enzyme (FGE), the cysteine of the tag is converted to a reactive aldehyde group. This electrophilic group can be targeted by an array of aldehyde-specific reagents, such as aminooxy- or hydrazide-functionalized compounds.
Analgesics are frequently used in combination, such as the paracetamol and codeine preparations found in many non-prescription pain relievers. They can also be found in combination with vasoconstrictor drugs such as pseudoephedrine for sinus-related preparations, or with antihistamine drugs for people with allergies. While the use of paracetamol, aspirin, ibuprofen, naproxen, and other NSAIDs concurrently with weak to mid-range opioids (up to about the hydrocodone level) has been said to show beneficial synergistic effects by combating pain at multiple sites of action, several combination analgesic products have been shown to have few efficacy benefits when compared to similar doses of their individual components. Moreover, these combination analgesics can often result in significant adverse events, including accidental overdoses, most often due to confusion that arises from the multiple (and often non-acting) components of these combinations.
Evolutionary biology is a subfield of biology that analyzes the mechanisms of evolution. Evolution accounts for the unity and diversity of life on Earth; Theodosius Dobzhansky famously said "nothing in biology makes sense except in the light of evolution". Population genetics for example studies how genetic variation develops, how it is inherited, and how the evolutionary mechanisms shape a population's genetic composition. Research in evolutionary biology covers many topics and incorporates ideas from diverse areas, such as molecular genetics and mathematical and theoretical biology. Some fields of evolutionary research try to explain phenomena that were poorly accounted for in the modern evolutionary synthesis. These include speciation, the evolution of sexual reproduction, the evolution of cooperation, the evolution of ageing, and evolvability. Ecology is the study of the distribution and abundance of life, the interaction between organisms and their environment.
"Biosafety in Microbiological and Biomedical Laboratories", official CDC guide. "Prevention of Biological Hazards", EU-OSHA "Symbol Making", an account of the development of the symbol in 1966. "BioSeal Systems", Biosafety level 4 containment. Biohazard Remediation Compliance Overview "Example of Reclassified Biohazard to Level 4", article from The Lancet concerning the reclassification of Ebola after observation. "Biological hazards related to working alone safety", an article focusing on working alone safety when dealing with biological hazards
Sources: en.wikipedia.org
APEKTx1 is a highly selective blocker of the voltage-gated potassium channel Kv1.1 with no effect on other tested potassium channels (Kv1.2, Kv1.3, Kv1.4, Kv1.5, Kv1.6, Shaker IR, Kv2.1, Kv3.1, Kv4.2 and Kv4.3). APEKTx1 selectively blocks Kv1.1 channels with an IC50 value of 0.9 nM, which makes it between a 700 to 3000 times more potent inhibitor than the two known sea anemone peptides targeted against Kv channels (kalicludines and SHTX II). APEKTx1 is thought to interact with Kv1.1 through the aliphatic residue alanine (A352), an acidic residue glutamate (E353), and an aromatic residue tyrosine (Y379), as a mutation in these sites causes a loss in affinity of the toxin for Kv1.1. These residues are located in the H5-loop between the S5 and S6 domains and are part of the channel’s pore. In addition, APEKTx1 acts as a potent trypsin inhibitor (Kd= 124 nM), probably a competitive one. However, trypsin inhibition is more potent (as it has a higher affinity) in BPTI, which can be explained by the presence of Phe13 and Pro19 in APEKTx1, causing an unfavorable interaction.
From the 17th century, and before modern developments in organic chemistry nomenclature, acetone was given many different names. They included "spirit of Saturn", which was given when it was thought to be a compound of lead and, later, "pyro-acetic spirit" and "pyro-acetic ester". Prior to the name "acetone" being coined by French chemists, it was named "mesit" (from the Greek μεσίτης, meaning mediator) by Carl Reichenbach, who also said that methyl alcohol consisted of mesit and ethyl alcohol. Names derived from mesit include mesitylene and mesityl oxide which were first synthesised from acetone. In 1839, the name "acetone" began to be used, because it was obtained from acetic acid. Unlike many compounds with the acet- prefix which have a 2-carbon chain, acetone has a 3-carbon chain. That has caused confusion because there can not be a ketone with 2 carbons. The prefix refers to acetone's relation to vinegar (acetum in Latin, also the source of the words "acid" and "acetic"), rather than its chemical structure.
Libraries of peptide aptamers have been used as "mutagens", in studies in which an investigator introduces a library that expresses different peptide aptamers into a cell population, selects for a desired phenotype, and identifies those aptamers that cause the phenotype. The investigator then uses those aptamers as baits, for example in yeast two-hybrid screens to identify the cellular proteins targeted by those aptamers. Such experiments identify particular proteins bound by the aptamers, and protein interactions that the aptamers disrupt, to cause the phenotype. In addition, peptide aptamers derivatized with appropriate functional moieties can cause specific post-translational modification of their target proteins, or change the subcellular localization of the targets.
Within the field of supramolecular polymerization, Schmatloch et al. used automated synthesis to create main-chain supramolecular coordination polymers, reacting bis(2,2′:6′,2″-terpyridine)-functionalized poly(ethylene oxide) with various metal(II) acetates. From this, it was revealed that classical laboratory approaches could be transferred to automatic synthesis, optimizing the processes to increase efficiency and aid with reproducibility.
Cervical drug delivery is a route of carrying drugs into the body through the vagina and cervix. This is a form of localized drug delivery that prevents the drugs from impacting unintended areas of the body, which can lower side effects of toxic drugs such as chemotherapeutics. Cervical drug delivery has specific applications for a variety of female health issues: treatment of cervical cancer, pregnancy prevention, STD prevention, and STD treatment.
Sources: en.wikipedia.org
The alpha-1B adrenergic receptor (α1B-adrenoreceptor), also known as ADRA1B, is an alpha-1 adrenergic receptor, and also denotes the human gene encoding it. The crystal structure of the α1B-adrenergic receptor has been determined in complex with the inverse agonist (+)-cyclazosin. There are 3 alpha-1 adrenergic receptor subtypes: alpha-1A, -1B and -1D, all of which signal through the Gq/11 family of G-proteins and different subtypes show different patterns of activation. They activate mitogenic responses and regulate growth and proliferation of many cells. This gene encodes alpha-1B-adrenergic receptor, which induces neoplastic transformation when transfected into NIH 3T3 fibroblasts and other cell lines. Thus, this normal cellular gene is identified as a protooncogene. This gene comprises 2 exons and a single large intron of at least 20 kb that interrupts the coding region. Antagonists L-765,314 Risperidone Brexpiprazole Tamsulosin Alpha-1B adrenergic receptor has been shown to interact with AP2M1. A role in regulation of dopaminergic neurotransmission has also been suggested.
In Taiwan, the Taiwan Transportation Safety Board (TTSB) is the independent government agency that is responsible for major transportation accident investigations. TTSB's predecessor was ASC, which was established in 1998. TTSB is under the administration of the Executive Yuan and independent from Civil Aviation Administration. The TTSB consisted of five to seven board members, including a chairman and a vice chairman, appointed by the Premier. The managing director of TTSB manages the day-to-day function of the organization, including accident investigations. In the United Kingdom, the agency responsible for investigation of civilian air crashes is the Air Accidents Investigation Branch (AAIB) of the Department for Transport. Its purpose is to establish the circumstances and causes of the accident and to make recommendations for their future avoidance.
Acanthosis nigricans-muscle cramps-acral enlargement syndrome, also known as Acanthosis nigricans-insulin resistance-muscle cramps-acral enlargement syndrome, is an extremely rare genetic disorder which is characterized by the appearance of acanthosis nigricans, insulin resistance, muscle cramps of severe intensity, and acral hypertrophy/enlargement. Only 2 cases have been reported in medical literature. It was first discovered when Jeffrey Flier and his colleagues described two siblings of the opposite sex with the symptoms mentioned above. (plus: large, chunky hands), the sister had virilized polycystic ovaries. After being treated with dilantin, the cramps' severity lowered and the brother's insulin resistance also lowered. The inheritance pattern of this disorder is thought to be autosomal recessive.
After translation, the AGP protein backbones are highly decorated with complex carbohydrates, primarily type II AG polysaccharides. The biosynthesis of the mature AGP involves cleavage of the signal peptide at the N-terminus, hydroxylation on the P residues and subsequent glycosylation and in many cases addition of a GPI-anchor. Glycosylation of the AGP backbone is suggested to initiate in the ERTooltip endoplasmic reticulum with the addition of first Gal by O-galactosyltransferase, which is predominantly located in ER fractions. Chain extension then occurs primarily in the GA. For those AGPs that include a GPI anchor, addition occurs while co-translationally migrating into the ER.
. It is used as a measure of affinity, with higher values indicating a lower affinity. For the given equation (E = enzyme, S = substrate, P = product), E + S ⟺ k − 1 k 1 E S ⟺ k 2 E + P {\displaystyle E+S{\overset {k_{1}}{\underset {k_{-}{1}}{\Longleftrightarrow }}}ES{\overset {k_{2}}{\Longleftrightarrow }}E+P} k d {\displaystyle k_{d}} would be equivalent to k − 1 / k 1 {\displaystyle k_{-1}/k_{1}} , where k 1 {\displaystyle k_{1}} and k − 1 {\displaystyle k_{-1}} are the rates of the forward and backward reaction, respectively in the conversion of individual E and S to the enzyme substrate complex. Information theory allows for a more quantitative definition of specificity by calculating the entropy in the binding spectrum. The chemical specificity of an enzyme for a particular substrate can be found using two variables that are derived from the Michaelis-Menten equation. k m {\displaystyle k_{m}} approximates the dissociation constant of enzyme-substrate complexes. k c a t {\displaystyle k_{cat}}
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.