Everything below concerns HPLC. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2025-10-25. Where a claim depends on a specific study, the study is described rather than over-claimed.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Nonpolar stationary phase with polar mobile phase |
| Typical column particle size | 3–5 µm | Smaller particles improve resolution but raise pressure |
| Typical flow rate | 0.5–2.0 mL/min | Depends on column dimensions and pressure limits |
| Common detection | UV-Vis absorbance | Requires analytes with chromophores |
| Typical run time | 5–30 min | Varies with method, gradient, and sample complexity |
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
In 1955, a USAF surgeon who advised the US Surgeon General wrote an article on how to make cars safer for those riding in it. Aside from the usual safety features, such as seat belts and padded dashboards, bumper shocks were introduced. In 1956, Ford tried unsuccessfully to interest Americans in purchasing safer cars with their Lifeguard safety package. (Its attempt nevertheless earns Ford Motor Trend's "Car of the Year" award for 1956.) In 1958, the United Nations established the World Forum for Harmonization of Vehicle Regulations, an international standards body advancing auto safety. Many of the most life saving safety innovations, like seat belts and roll cage construction were brought to market under its auspices. That same year, Volvo engineer Nils Bohlin invented and patented the three-point lap and shoulder seat belt, which became standard equipment on all Volvo cars in 1959. Over the next several decades, three-point safety belts were gradually mandated in all vehicles by regulators throughout the industrialised world. In 1959, American Motors Corporation offered the first optional head rests for the front seat. Also in 1959, the Cadillac Cyclone concept by Harley Earl had "a radar-based crash-avoidance system" located on the nose cones of the vehicle that would make audible and visual signals to the driver if there were obstacles in the vehicle's path.
Different amino-acid sequences have different propensities for forming α-helical structure. Alanine, uncharged glutamate, leucine, charged arginine, methionine and charged lysine have especially high helix-forming propensities, whereas proline and glycine have poor helix-forming propensities. Proline either breaks or kinks a helix, both because it cannot donate an amide hydrogen bond (because it has none) and because its sidechain interferes sterically with the backbone of the preceding turn – inside a helix, which forces a bend of about 30° in the helix's axis. However, proline is often the first residue of a helix, presumably due to its structural rigidity. At the other extreme, glycine also tends to disrupt helices because its high conformational flexibility makes it entropically expensive to adopt the relatively constrained α-helical structure.
ADPRase is a dimer of two identical monomers, each of which contain 209 amino acids. The two monomers are folded into two distinct structural domains and with two equivalent catalytic sites. The C-terminal domain consists of the Nudix sequence mentioned above and the N-terminal domain is primarily involved in dimer stabilization. As noted earlier, the Nudix fold is the catalytic part of the enzyme, but both domains are involved in the active site and they both help with the attachment and coordination of H2O, Mg2+, and the ADP-ribose substrate.
Sources: en.wikipedia.org
Topical analgesia is generally recommended to avoid systemic side-effects. Painful joints, for example, may be treated with an ibuprofen- or diclofenac-containing gel (The labeling for topical diclofenac has been updated to warn about drug-induced hepatotoxicity.); capsaicin also is used topically. Lidocaine, an anesthetic, and steroids may be injected into joints for longer-term pain relief. Lidocaine is also used for painful mouth sores and to numb areas for dental work and minor medical procedures. In February 2007 the FDA notified consumers and healthcare professionals of the potential hazards of topical anesthetics entering the bloodstream when applied in large doses to the skin without medical supervision. These topical anesthetics contain anesthetic drugs such as lidocaine, tetracaine, benzocaine, and prilocaine in a cream, ointment, or gel.
Risk of developing CJD increases with age. CJD incidence was 3.5 cases per million among those over 50 years of age between 1979 and 2017. Approximately 85% of CJD cases are sporadic, and 10–15% of CJD cases are due to inherited mutations of the prion protein gene. CJD deaths and age-adjusted death rate in the United States indicate an increasing trend in the number of deaths between 1979 and 2017. Although not fully understood, additional information suggests that CJD rates in nonwhite groups are lower than in whites. While the mean onset is approximately 67 years of age, cases of sCJD have been reported as young as 17 years and over 80 years of age. Mental capabilities rapidly deteriorate and the average amount of time from onset of symptoms to death is 7 to 9 months. According to a 2020 systematic review on the international epidemiology of CJD:
Amivantamab, sold under the brand name Rybrevant, is a bispecific monoclonal antibody used to treat non-small cell lung cancer. Amivantamab is a bispecific epidermal growth factor (EGF) receptor-directed and MET receptor-directed antibody. It is the first treatment for adults with non-small cell lung cancer whose tumors have specific types of genetic mutations: epidermal growth factor receptor (EGFR) exon 20 insertion mutations. The most common side effects include rash, infusion-related reactions, skin infections around the fingernails or toenails, muscle and joint pain, shortness of breath, nausea, fatigue, swelling in the lower legs or hands or face, sores in the mouth, cough, constipation, vomiting and changes in certain blood tests. Amivantamab was approved for medical use in the United States in May 2021, and in the European Union in December 2021. The US Food and Drug Administration considers it to be a first-in-class medication.
Sources: en.wikipedia.org
Immobilized metal ion affinity chromatography (IMAC) is based on the specific coordinate covalent bond of amino acids, particularly histidine, to metals. This technique works by allowing proteins with an affinity for metal ions to be retained in a column containing immobilized metal ions, such as cobalt, nickel, or copper for the purification of histidine-containing proteins or peptides, iron, zinc or gallium for the purification of phosphorylated proteins or peptides. Many naturally occurring proteins do not have an affinity for metal ions, therefore recombinant DNA technology can be used to introduce such a protein tag into the relevant gene. Methods used to elute the protein of interest include changing the pH, or adding a competitive molecule, such as imidazole.
The linear amino acid sequence of a protein is called the primary structure. The primary structure can be easily determined from the sequence of codons on the DNA gene that codes for it. In most proteins, the primary structure uniquely determines the 3-dimensional structure of a protein in its native environment. An exception is the misfolded prion protein involved in bovine spongiform encephalopathy. This structure is linked to the function of the protein. Additional structural information includes the secondary, tertiary and quaternary structure. A viable general solution to the prediction of the function of a protein remains an open problem. Most efforts have so far been directed towards heuristics that work most of the time.
The presence of autoantibodies against citrullinated proteins in rheumatoid arthritis patients was first described in the mid-1970s when the biochemical basis of antibody reactivity against keratin and filaggrin was investigated. Subsequent studies demonstrated that autoantibodies from RA patients react with a series of different citrullinated antigens, including fibrinogen, deiminated Epstein–Barr virus nuclear antigen 1 and vimentin, which is a member of the intermediate filament family of proteins. Several assays for detecting ACPAs were developed in the following years, employing mutated citrullinated Vimentin (MCV-assay), filaggrin-derived peptides (CCP-assay) and viral citrullinated peptides (VCP-assay). A 2006 clinical study showed that anti viral citrullinated peptide (VCP) antibodies of the IgG and IgA isotypes represent a discriminating specific marker of rheumatoid arthritis from other chronic arthritides and disease controls, suggesting an independent production of each isotype. In 2010, ACPA testing has become substantial part of The 2010 ACR-EULAR classification criteria for rheumatoid arthritis.
The AAV genome is built of single-stranded deoxyribonucleic acid (ssDNA), either positive- or negative-sensed, which is about 4.7 kilobase long. The genome comprises ITRs at both ends of the DNA strand, and two open reading frames (ORFs): rep and cap. The former is composed of four overlapping genes encoding Rep proteins required for the AAV life cycle, and the latter contains overlapping nucleotide sequences of capsid proteins: VP1, VP2 and VP3, which interact to form a capsid with icosahedral symmetry.
Sources: en.wikipedia.org
It separates components in a liquid sample and measures their amounts using a detector. Results can indicate concentration, purity, or identity based on retention time and detector response. The technique works for mixtures that can be dissolved and filtered.
It offers high resolution, reproducibility, and compatibility with many sample types. A single run can separate and quantify multiple analytes. It is common in pharmaceutical, food, environmental, and industrial laboratories.
Samples must be soluble in a suitable mobile phase and free of particles that can block the column. Detector response depends on analyte structure, so some compounds need derivatization or alternative detection. Complex matrices may require extensive sample preparation.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.